Product Description
Free Shipping
8 PIECE SET JETS KIT Product # 1020-400712
1. SOLDERING BOARD CERAMIC PLATE HEAT RESISTANT 5" x 5" SQUARE BLOCK JETS Product# 1922-4055 Made in USA
Specifications:
- Dimensions: 5" x 5" x 1/2" Thick (120mm x120mm x 12.7mm)
- Temperature Tolerance: Up to 2000ºF / 950ºC.
- Reflects Heat
- Ceramic (Non-Asbestos)
- Board Weight: 14oz.
2. SOLDERING PICK TITANIUM TIP NON ROLL HANDLE JETS Product # 1919-950 G (Handle Color may Vary)
Specifications:
- Overall Length: 6-1/2" - 165mm
- Pick Length: 2" - 53mm
- Handle: Non Rolling Handle NOTE (Hex End Head -Color may vary)
- Weight: 0.6oz. - 16gr
3. THIRD HAND BASE HELPING HAND BASE ONLY TWEEZER TOOL HOLDER 3RD HAND BENCH WORK JETS Product # 1418-101
Specifications:
- Base Material: Cast Iron
- Base Diameter: 2-1316" - 71.5mm
- Base Weight: 12.2oz
4. FIBER GRIP TWEEZERS CROSS LOCKING SELF CLOSING BENT TIP JETS Product # 1419-5018
Specifications:
- Overall length: 6-1/2”
- Tweezer Tip: Bent 45o - Serrated
- Weight: 2 oz
5. CROSS LOCK TWEEZER SHORT POINTED SELF CLOSING REVERSE ACTION JETS Product # 1419-5001
Specifications:
- Overall length: 4-3/4”
- Tweezer Tip: Pointed - Serrated
- Weight: 2 oz.
6. HANDY FLUX™ - Paste Made by Lucas Milhaupt 7oz. JETS Product # 1924-407
All purpose, low temperature flux Handy® Flux is a long lasting white paste type, very durable won’t break down from prolonged heat, an all-purpose flux for use in brazing and soldering Gold, Silver, Brass, Copper and other Non-Ferrous Metals. Flux is for torch brazing - NOT soldering iron.
Handy Flux is an active fluoride/borate-type flux which is appropriate for all nonferrous metals and begins to melt and dissolve oxides at 600°F, having an effective temperature range from1100° F-1600° F. Paste formula can be cleaned up with hot water. Handy Flux TM is widely used in Jewelry Making, by Silversmiths, and in Creative Arts.
Prior to soldering make sure joints and the solder are clean, flux the full surface area to prevent oxidation and allow for good solder flow, and a good brazed joint.
Soldering Note: Clean - Surface & Joint is important and not too much Solder, good even heat over entire joint area. Clean remove oxides and other soldering residues prior to finishing.
7. WIRE Solders Diameters 20ga - 0.032" - 0.81mm / Lengths: 12” JETS Product # 1925-45331
Soft/Easy Specifications:
- Solder: Silver Content of 65%
- Melt temperature: 1,240°F - 671°C
- Flow temperature: 1,325°F - 718°C
Medium Specifications:
- Solder: Silver Content of 70%
- Melt temperature: 1,275°F - 691°C
- Flow temperature: 1,360°F - 738°C
Hard Specifications:
- Solder: Silver Content of 75%
- Melt temperature: 1,365°F - 741°C
- Flow temperature: 1,450°F - 788°C
8. SHEET Solders Measure: 1" x 1" Square - Weight 1Dwt – 1.5Gr JETS Product # 1925-45223
SOFT/EASY SPECIFICATIONS:
- Solder: Silver Content of 65%
- Melt temperature: 1260o F - 682oC
- Flow temperature: 1,325°F - 718°C
Medium Specifications:
- Solder: Silver Content of 70%
- Melt temperature: 1,295°F - 746°C
- Flow temperature: 1,360°F - 738°C
Hard Specifications:
- Solder: Silver Content of 75%
- Melt temperature: 1,375°F - 746°C
- Flow temperature: 1,450°F - 788°C
Attention: These solders are made to be used with high heat torch or butane torch in order to reach melting temperature, it is not intended to be used with soldering iron.
